联系我们Contact us

龙盛门业上海快3
联系人: 夏经理
座机: 4006080090
手机: 13940183063
QQ: 260793122
地址: 市府大路58-3号

「不锈钢升降柱」自动路桩接线方法

您现在的位置是:上海快3>>新闻中心>>技术中心

「不锈钢升降柱」自动路桩接线方法

发布日期:2019/7/10 13:24:39



「不锈钢升降柱」自动路桩接线方法





Automatic Pile Connection Method for "Stainless Steel Lifting Column"






1、路桩设施动力单元预留线:




1. Reserved line for dynamic unit of road pile facility:




路桩动力单元电机是一条三芯电缆线依次为蓝线。棕线、花线、电磁阀为两根黑线、带警示灯的有一条两芯螺旋灯线,共七根线,不带警示灯的共五根线,预埋桶固定钢筋焊接实现后开始接线。




The motor of power unit of road pile is a three-core cable which is blue in turn. Brown thread, flower thread and solenoid valve are two black lines, with a warning lamp and a two-core spiral lamp line. There are seven lines and five lines without warning lamp. The connection begins after the welding of fixed steel bars in embedded barrels.








2、接线流程:




2. Wiring process:
  


把动力单元液压一体机放在预埋桶基本沟一侧的地面上,把预埋桶上方引出的七芯电缆,分别接到动力单元的电机线、电池阀线、警示灯线上。




The hydraulic integrator of the power unit is placed on the ground on the side of the basic ditch of the buried barrel, and the seven-core cable drawn from the top of the buried barrel is connected to the motor wire, battery valve wire and warning light line of the power unit respectively.




准确记清楚七芯线电缆线的线号或颜色,与设施上的电机,电池阀、警示灯所对应的线号颜色,以免控制箱接错线。




Accurately remember the line number or color of the seven-core wire and cable, and the corresponding line number color of the motor, battery valve and warning lamp in the facility, so as to avoid misconnection of the control box.





  
3、设施接线说明:




3. Facilities wiring instructions:




路桩上电机线3根线蓝色电机上、棕色电机下、划线电机公用,接在控制箱所对应的端子上不可接反。




The motor wires on the pile are common to the blue motor, the brown motor and the marking motor, which can not be connected to the terminal corresponding to the control box.




电池阀2根单独的黑色线,接在控制箱电池阀、电池阀公用对应端子上,不分正负。警示灯线1根两心线接在控制箱警示灯、警示灯公用端子上,不分正负。
  


Two separate black wires of the battery valve are connected to the common corresponding terminals of the control box battery valve and the battery valve, regardless of positive or negative. The warning light line is connected to the warning light of the control box and the public terminal of the warning light, regardless of positive or negative.







4、接线标准:




4. Wiring standards:




线头接好后要求用焊锡焊接好,先用塑料胶带缠好,再用高压防水胶带缠两层,然后在用塑料胶带缠实,后用电工沥青胶布缠好,一共包四次,线接好后把接线端的电线整理规范,固定在动力单元的下方,阻止外力把接线处拉断。




Wire ends should be welded by soldering tin, first wrapped with plastic tape, then wrapped with high-pressure waterproof tape, then wrapped with plastic tape, then wrapped with electrical asphalt tape, four times in total. After wiring is finished, the wiring at the wiring end should be regulated and fixed under the power unit to prevent external forces from pulling the wiring. Break.




整理好后先把动力单元上接警示灯的2根线连在一起,用万用表测量电缆线的另一端,3根线电机是通的、2根线电池阀是通的。
  


After finishing, two wires connected to the warning lamp on the power unit are connected together. The other end of the cable is measured by a multimeter. Three wires are connected to the motor and two wires are connected to the battery valve.




长春不锈钢升降柱2根灯线是通的,电机、电池阀、电线之间是不可以通的,确认后将动力单元放入预埋桶内,对正预埋桶下方的固定螺栓,顺时针转动液压动力单元按钮,可以用木棍等,把剩余的电缆线,规范地盘到液压动力单元的




Two light wires are connected, and the motor, battery valve and wire are not connected. After confirmation, the power unit is put into the buried barrel. For the fixed bolt under the buried barrel, the hydraulic power unit button can be rotated clockwise, and the remaining cable can be used with wooden sticks to standardize the site to the hydraulic power unit.




在线客服
分享
上海快3开奖结果 上海快3 大家乐彩票注册 上海快3走势图 上海快3 上海快3 上海快3平台 上海快3开奖结果 上海快3 上海快3平台